The built-in Premium 2.0 opens the 2026 generation of ÜLKA nail dust collectors. Its airflow reaches 4.4 m/s against 3.3 on the previous version, at identical power.
The housing sits beneath the worktop with only the grille flush: the table stays entirely free. HEPA filtration, 52 W, five-year warranty.
The built-in unit has always been the choice of stations set up to last: the device disappears under the table, the grille sits flush, and nothing clutters the working surface. The 2026 version keeps that principle and fixes the one complaint made about its predecessor: it did not pull fast enough.
Airflow rises from 3.3 to 4.4 metres per second, a third more, without drawing a single extra watt. The grille has been entirely redrawn.
Rather than a speech, a measurement. Point by point, the gap between the two built-in units:
| Criterion | Premium built-in | Premium 2.0 built-in | Difference |
|---|---|---|---|
| Airflow | 3.3 m/s | 4.4 m/s | + 33 % |
| Power drawn | 52 W | 52 W | identical |
| Housing height | 9.7 cm | 11 cm | + 1.3 cm |
| Width and depth | 28 × 26 cm | 28.1 × 26 cm | near identical |
| Mass | 2.25 kg | 2.1 kg | - 150 g |
| Warranty | 5 years | 5 years | unchanged |
One line deserves your attention before ordering: the housing has gained 1.3 cm in height. If you are replacing a first-generation built-in Premium, check the clearance beneath your worktop — the surface cut-out itself is practically unchanged.
ÜLKA uses the name Human Engineering for a design method that is simple to state: watch how a nail technician actually works first, draw afterwards. Not the other way round.
Three observations shaped this model. Dust is born on a band two or three centimetres wide, at the edge of the nail, not across the whole hand. The client moves her hand constantly; she never holds it still in the middle of a grille. And a nail station worktop is already saturated long before you add a device to it.
From those come the geometry of the new grille, the speed of the airflow and the decision to house the body beneath the worktop. Each of those decisions answers one of the three constraints.
On the previous generation, the grille simply let air through. On the 2.0 it steers it. Its pattern channels suction toward the band where filings form, across a widened capture area.
The benefit is measured in tolerance rather than raw power. You no longer have to pull your client's hand back to the centre of the unit every couple of minutes for suction to stay effective: the useful zone now covers the natural range of the gesture.
That is the reason this version exists. The body sits beneath the worktop, in a cut-out, with only the grille flush with the table. Lamp, e-file, bottles and brushes reclaim the space a desktop unit would take from them.
For the client the benefit is more direct still: her hand rests flat on the table, with no step to clear and no suspended wrist. Over a full set, that is the difference between a position that holds and one that tires — and a tired hand moves, which shows in your work.
The body measures 28.1 × 26 × 11 cm and weighs 2.1 kg.
Power has not moved: 52 W, as on the previous generation. That is precisely what makes the gain interesting. Airflow grows by a third without consuming more, which means the progress comes from the path of the air and the design of the grille, not from a bigger motor.
The unit accepts 220 V / 50 Hz as well as 110 V, and is sized to run uninterrupted through a full day of appointments.
A built-in unit is not unpacked, it is installed. Three things to settle before ordering.
The cut-out. The housing needs an opening in the worktop matching the device. If your nail table was sold with a built-in collector recess, it is probably compatible: simply check the 28.1 × 26 × 11 cm dimensions. Otherwise the cut-out must be made before delivery.
The depth. This is the point not to overlook if you are replacing a first-generation model: the 2.0 is 1.3 cm taller. Measure what you have beneath the worktop, drawer or cross-rail included.
The alternative. If your table cannot be cut — rented premises, an antique piece, a mobile setup — the Premium 2.0 also exists as a tabletop version, with the same 4.4 m/s airflow in a 10.6 cm desktop housing. Both are among our ÜLKA nail dust collectors.
A dust collector never works alone. Three items in the ÜLKA catalogue pair naturally with it:
| Device type | Built-in nail dust collector |
| Power | 52 W |
| Maximum airflow | 4.4 m/s |
| Supply | 220 V / 50 Hz — 110 V compatible |
| Filtration | HEPA cartridge |
| Grille | New pattern, wide capture area |
| Mass | 2.1 kg |
| Housing dimensions | 28.1 × 26 × 11 cm |
| Model year | 2026 |
| Cover | 5 years |
The working life of a nail dust collector is decided almost entirely by the filter. Here is the routine, in order:
Wear parts are gathered in our ÜLKA consumables. As the Premium 2.0 carries a newly drawn grille, write to us before ordering a replacement filter or grille: we will confirm the reference matched to your unit.
It succeeds it, but both stay in the catalogue while stock lasts. The gap comes down to one point, and it is clear: 4.4 m/s against 3.3, at the same 52 W. If you are fitting out a new station, take the 2.0.
Margin. A fast airflow keeps drawing particles in even when the hand moves a few centimetres away from the grille — which happens constantly as soon as you turn a finger or change angle. A slow unit captures properly only in a narrow zone, and everything outside it lands on the table.
That is the use case that demands it most. A professional ÜLKA e-file throws material continuously and at speed, right at the nail. Without fast capture, that dust spreads across the whole working area before it can be drawn in.
They tell you about electrical consumption, not effectiveness. The Premium 2.0 proves it: at strictly identical power, 52 W, it produces an airflow a third faster than the previous generation. What makes the difference is turbine design, grille geometry and the area offered to suction.
Yes, unless it is already prepared for a built-in collector, which many professional models are. The cut-out must take a housing of 28.1 × 26 × 11 cm. Have it made before delivery rather than after.
In width and depth, yes: 28.1 × 26 cm against 28 × 26 cm, a millimetre apart. The new housing is however 1.3 cm taller, 11 cm against 9.7. Measure the clearance beneath the worktop before ordering.
No, this model is designed to be built in: its housing is not meant to stay visible. If you cannot cut your worktop, choose the tabletop version of the Premium 2.0, which offers exactly the same 4.4 m/s airflow.
That is what it is sized for. Its 52 W are intended for continuous salon operation, without heat build-up or the gradual drop in airflow that shows up late in the day.
It holds the particles the airflow has captured. Without it, the unit would simply move dust from one part of the room to another. It is the wear part of the system, and the only one the lifespan of the whole really depends on.
A daily dry dusting at the end of the day, and replacement roughly every three months. If you see eight clients a day, shorten that; if you work part time, it stretches naturally. Our ÜLKA consumables gather the spare parts.
Never. Water spreads the fibres of the filtering media irreversibly: the filter then lets through the finest particles, exactly the ones that matter. Soft brush or air blower, nothing else.
Yes, and those are the services where it earns its place most. Removal, infills, shaping extensions: any operation that produces filings falls within its remit.
It accepts 220 V / 50 Hz and 110 V, which covers most domestic supplies.
Five years, a span few manufacturers offer on equipment of this kind. Service is handled by ÜLKA France, with spare parts held in the catalogue: you have no claim to open abroad.
ulka.fr is the brand's official site in France. Buying here means a contact who answers in your language, spare parts held locally and a five-year warranty exercised without an intermediary.
To place the Premium 2.0 among the other models, browse the whole of our ÜLKA nail dust collectors.
The built-in Premium 2.0 opens the 2026 generation of ÜLKA nail dust collectors. Its airflow reaches 4.4 m/s against 3.3 on the previous version, at identical power.
The housing sits beneath the worktop with only the grille flush: the table stays entirely free. HEPA filtration, 52 W, five-year warranty.
ÜLKA is the essential reference for nail dust collectors. Specially designed for nail professionals and beauty salons, our dust extractors ensure a healthier work environment by effectively capturing fine particles generated during nail filing and sanding.
Recognized for the quality and reliability of its equipment, the ÜLKA brand offers robust devices designed for intensive use with a lifespan of up to 50,000 hours. Our products are European certified, ensuring safety and performance for nail technicians, beauticians, and beauty technicians.
